Quantcast Install the Center Blast Deflector, Kit P/N 106706-3. (cont)

 

Click here to make tpub.com your Home Page

Page Title: Install the Center Blast Deflector, Kit P/N 106706-3. (cont)
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Install the Center Blast Deflector, Kit P/N 106706-3.
Up
TB-9-2320-279-13-P-2 Concrete Protection Kit for M977 Series Heavy Expanded Mobility Tactical Trucks (HEMTT) Manual
Next
Figure 39. Position the Center Blast Deflector onto the Mounting Bracket Studs.
II106700-5
Rev. B
Page 67
1. Apply Loctite 242 to four bolts (0.750 10 x 2.000 LG) and install the bolts into
the driver's-side Center Blast Deflector Bracket (P/N 106753-1) and the
passenger-side Center Blast Deflector Bracket (P/N 106754-1). At this time,
install the bolts only three turns to allow for adjustment.
2. Install the driver's-side Center Blast Deflector Bracket (P/N 106753-1) onto the
frame rail. Install the driver's-side Center Blast Deflector Bracket with the
forward surface against the rear edge of the crossmember (see Figure 36).
3. Install the passenger-side Center Blast Deflector Bracket (P/N 106754-1) onto the
frame rail. Install the passenger-side Center Blast Deflector Bracket with the
forward surface against the rear edge of the crossmember brace (see
4. Torque the four attachment bolts (0.750 10 x 2.000 LG) to 280 ft-lb.
NOTE
Install the driver's-side Center Blast Deflector tab (with the bolt holes) on top of the
driver's-side Blast Deflector, the spacer (P/N 106777-1) between the Center Blast
Deflector tab and the driver's-side Blast Deflector, and the passenger-side Center
Blast Deflector tab (with the bolt holes) on the bottom of the passenger-side Blast
Deflector. This can be accomplished by twisting the Center Blast Deflector and
raising it into place until the driver's-side tab is above the driver's-side blast deflector
and then straightening it into the proper position to allow assembly.
The previously separated steering linkage must be aligned through the cutout on the
driver's side of the Center Blast Deflector (P/N 106715-1) during installation.
5. Using a floor jack or other suitable lifting device, position the Center Blast
Deflector (P/N 106715-1) to the Mounting Bracket Studs (See Figure 39).
6. Secure the Center Blast Deflector to the Mounting Bracket Studs using
six flat washers (3/4 ID) and locknuts (3/4 10) (See Figure 40).
7. Torque the six locknuts (3/4 10) to 280 ft-lb.
8. Install four bolts (3/4 10 x 2.000 LG), eight flat washers (0.750 ID), and
four locknuts (3/4 10) through the matching bolt holes between the inside edge
(engine side) of the passenger-side Blast Deflector and the outside edge
(passenger side) of the Center Blast Deflector. Hand-tighten the locknuts.
0039 00-77

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.
6230 Stone Rd, Unit Q Port Richey, FL 34668

Phone For Parts Inquiries: (727) 493-0744
Google +